Installation Process

Place the motherboard on top of the casing in the right place



The motherboard is properly located




Attach Bolt Lock



The motherboard is mounted



Install Processor (Remember the triangle mark position near the hinge lock)



Processor is in the correct position



Press Lock



Processor has been installed correctly



Install Heatsink



Press the lock with a special tool



Heatsink installed correctly




Connect the Processor Fan Cable



The cable is mounted



Open lock RAM



Install RAM in a way suppressed




Lock locks by itself and installed RAM




Do the same with the other RAM




RAM installed correctly




Install the VGA card




Press the VGA card and do not forget to attach penguncinya




VGA card is installed




Attach Bolt Lock




True VGA card installed




Connect the Reset Switch Cable




Reset Switch Cable Already Installed




Replace Power Switch Cable




Already Installed Power Switch Cable




Replace the HDD cable indicator




Already Installed HDD cable Indicator




Install Cables VCC




Connect the USB Cable Panel




Replace the front panel Microphone Cables etc.




All cables have been installed




Install Power Supply Cables




Cable Power Supply is mounted




Replace the hard drive (be careful not to reverse)




Tighten the lock screw (do not forget the other side too)




Put Floppy drive




Replace the bolt lock (do not forget the other side too)




Install CD ROM




Replace the bolt lock (do not forget the other side too)




Install DVD ROM



Replace the bolt lock (do not forget the other side too)



Put Floppy Cables



Put Floppy Cable on Motherboard




Install the Optical Drive Cable




Install Optical Cable Drive In accordance with the optical drive




Put on the Hard Drive IDE Cables




Replace IDE hard drive cable in the Primary Slot




Put in the DVD ROM IDE Cable




Put in the CD ROM IDE Cable




Attach IDE Cable CD & DVD ROM on Secondary slot




Install the Optical Drive Power Cable



Install FDD and Hard Disk Power Cable




Connect the fan cable




Already Cable Installed




Attach Bolt Lock Case




Attach Bolt Lock Case




Installation Completed Selengkapnya...

Unloading computer

Already Cable Pulled
Unplug the HDD cable indicatorKabel Already dicabutCabut SpeakerSpeaker Already dicabutCabut Cardepaskan Lock Bolt Buffer VGA VGA CardPengunci already dilepasTarik slightly separated from the lock-up for
Drag and drop
VGA Card has been removed
VGA card that has dilepasBuka RAMRAM Will Lock Up with sendirinyaCabut RAMRAM been revoked
Open Lock-Up with Will RAMRAM sendirinyaCabut Fruit RAM2 RAM heatsinks lock had been removed Congkel dngn special tool
This caution is very difficult jd



Finally taken out also



Heatsink successfully removed



Heatsink that has been released



Pull / Press Lock Processor



Processor will go up by itself



Remove the Processor (Do not hold the bottom)



Save juncture safe and untouched by any pin



Remove the bolt lock Motherboard



Slide the motherboard to not get caught I / O shield



Lift Motherboard



Already removable motherboard



Case Empty with no component Selengkapnya...

Tips on How to Re-Install Windows XP SP 2

1

Previously you needed a master Windows XP CD first and then input in the CDROM / DVDROM you. Then restart your computer, then appears to look like the image and press the Delete key on the keybord so that you can enter the BIOS (Basic Input Output System) computer. In some types of Mainboard must press the F2 key on the keyboard. You can see it on the command Press DEL to run Setup.

2

Then you will be in the BIOS and then select Boot on the menu and select Boot Device Priority items as shown.

3

After that you change the [CDROM] in the position of 1st Boot Device to boot from the CD-ROM by using the + - in keyboard.Lalu press F10 to save your configuration.

4

Restart the computer, wait until it says something like this and then press any key quickly.

5

After the following display and press Enter to go to the process of installing or R to repair Windows on Recovery consule or F3 to end the install process.

6

Continue on Lisencing Agreement for further press F8 and ESC to abort the process.

7

In the figure the position of the partition has not been filled by the system windows.Tekan C to create a new partition on the hard drive and Enter to install.

8

Then input how much capacity you want to create partitions in units of megabytes (MB) and press Enter to create a partition as shown in the picture.

9

Then press Enter to do the install or Delete to delete the partition.

10

And select the NTFS file system (Quick) or FAT file system (Quick) and press Enter.

11

When the installation process step 1 → 10 true then it will look like the picture.

12

After that you arrive at the following screen Click Next....

13

Then fill in with Name and Organization You then press Next.

14

Here you will fill in the Product Key or Serial Numbers of the type of windows you press Next again.

15

Enter the computer name and password to access it and press Next.

16

Set Time Zone at the position (GMT +80:00), click Next.

17

Typical settings: In this option will be made the default network settings of Windows and Custom settings: For setting up your network manually and then click Next.

18

When you connect kejaringan locally with a domain select the option Yes, then fill with the same name DOMAIN DOMAIN network and vice versa if you do not connect kejaringan or connected but without DOMAIN select the option No, once again press Next.

finish

Next Kamutinggal click Ok, Next, Skip and Finish are also asked to fill in your name. until you are on the Windows desktop display like this. Now you live CPU you install hardware drivers.
Selengkapnya...